
打膠機的膠頭有異物的幾個危害
時間:2017-10-09 來源:http://www.bjrcc.com.cn/ 發布人:昌盛機械
導致中空玻璃密封不嚴產生漏氣的原因有哪些。
What are the reasons for the leakage of insulating glass and the leakage of insulating glass?.
一、操作問題
I. operation problems
1、打開氣泵開關,電源總開關,控制臺開關,在控制臺按手動按鈕,我們將打膠機膠頭讓他回位到原點,這是我們要對打膠機的速度進行下調節(一般情況下使用我們設置好的速度即可),密封不嚴可能是由于打膠機的打膠速度過快而我們的鋁條安裝的時候深淺不一所以導致中空玻璃的密封膠在鋁條深的地方會出現密封不嚴的情況。
1, the first open air pump switch, power switch, control switch, manual button on the console, we will glue machine glue head let him return to the origin, this is we want to fight the glue machine speed regulation (we use set speed under normal circumstances can not seal), may be the glue machine glue fast and our aluminum strips when installing shades resulting in insulating glass sealant in aluminum deep place will be sealed and lax circumstance.
2、然后是混交了,按桶膠按鈕,按工作選擇按鈕,然后按拍膠啟動,在按伐開,此時膠頭以出膠,等看不見白膠,以混均勻以后按伐關,此時我們就可以進行正常的打膠機工作了。
2, then is mixed, according to the first barrel of plastic button, and then press the select button according to the work, take glue start in cutting, the rubber head to glue, such as invisible glue, to mix well after the press cutting off, we can carry out normal atx-ii work at this time.

3、打膠之前注意觀察打膠機的膠頭是否有玻璃參差等異物出現,如果將其摻入密封膠內那么我們的中空玻璃的密封效果肯定就不會有那么好了。
3, before playing glue, pay attention to observe the rubber head of the glue machine, whether there is a glass uneven and other foreign bodies appear, if it is incorporated into sealant, then the sealing effect of our insulating glass will certainly not be so good.
二、物料問題
Two material problems
1、出現中空玻璃打膠機生產出來的中空玻璃密封不好的另一大主要原因就是我們的鋁條安裝過于隨意~~~盡管我們的設備無需進行設置可全自動的檢測并處理深淺不一的鋁條,但是如果差距太大且打膠速度過快的話也是有可能發生中空玻璃密封不嚴漏氣的情況。
1, hollow glass hollow glass glue machine produced not sealed another major reason is that our aluminum strip is installed too freely while our equipment ~ ~ ~ without setting aluminum automatic detection and processing depth, but if the gap is too large and too fast then glue it may occur hollow glass Mifengbuyan leak case.
2、膠體本身質量問題,這種情況我們不是沒有遇到過,但是這種情況發生的幾率非常的小,但是也非常的容易讓人忽略的一個問題,所以小編在這里還是有必要同大家說下這個原因。
2, the colloid quality problems, this situation we have encountered, but the probability of this happening is very small, a problem but also very easy to ignore, so small in here is necessary for the same people said this reason.
3、打膠機的供嬌壓力如果不夠的話也是會出現這個問題的,因為打膠機的膠體完全靠氣壓來擠出設備并完美的涂裝在中空玻璃的鋁條中的。如果壓力過小的話也會導致中空玻璃打膠機密封不嚴
3, if the pressure of the glue machine is insufficient, it will also appear this problem, because the glue of the glue machine is completely squeezed out by the air pressure equipment, and the perfect coating is in the aluminum strip of the hollow glass. If the pressure is too small, it will result in sealed glass sealing machine is not strict
本文由雙組份打膠機友情奉獻.更多有關的知識請點擊:http://www.bjrcc.com.cn/我們將用的技術.真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.
This paper consists of two components of atx-ii friendship devotion. More related knowledge: Please click http://www.bjrcc.com.cn/ we will use the most advanced technology. The most sincere attitude, to provide you with the most comprehensive service. More related knowledge and we will continue to offer. Please look forward to.
- 雙組份打膠機旋轉伺服報警810?這樣解決快速恢復生產 2026/01/16
- 中空玻璃加工設備:打膠機機頭升降鏈條松動?這樣調節精準又牢固 2026/01/14
- 中空玻璃生產線合片段橫梁調平指南:小誤差別忽視,這樣調精準又省心 2026/01/12
- 中空玻璃加工設備的合片段橫梁高低不平?這樣調,合片精準不跑偏 2026/01/11
- 中空玻璃加工設備板壓段卡殼?輪子走玻璃不走?這樣排查超高效 2026/01/10
- 中空生產線封膠線機頭立柱不平?這樣調整,封膠均勻不返工 2026/01/05
- 中空玻璃加工設備卡殼?液壓站不起壓?卡閥問題這樣解決超省心 2025/12/31
- 全自動封膠線卡殼?貼鋁條后玻璃不走、報警?這樣解決超簡單 2025/12/31
- 冬天中空玻璃生產線出輪子灰?。窟@些日常難題解決辦法請收好 2025/12/30
- 全自動封膠線的“智能眼”——LOW-E識別儀,守護封膠質量的關鍵 2025/12/30

當前位置:



產品分類Product categories
聯系我們Contact us
