1、雙組份打膠機本身質量問題，這種情況我們不是沒有遇到過，但是這種情況發生的幾率非常的小，但是也非常的容易讓人忽略的一個問題，所以小編在這里還是有必要同大家說下這個原因。

　　1, the colloid quality problems, this situation we have encountered, but the probability of this happening is very small, a problem but also very easy to ignore, so small in here is necessary for the same people said this reason.

　　2、出現中空玻璃打膠機生產出來的中空玻璃密封不好的另一大主要原因就是我們的鋁條安裝過于隨意，盡管我們的設備無需進行設置可全自動的檢測并處理深淺不一的鋁條，但是如果差距太大且打膠速度過快的話也是有可能發生中空玻璃密封不嚴漏氣的情況。

　　2, hollow glass hollow glass glue machine produced not sealed another major reason is that our aluminum installation is too arbitrary, although our equipment without setting aluminum automatic detection and processing depth, but if the gap is too large and too fast then glue it may occur hollow glass Mifengbuyan leak case.

　　3、打膠機的供嬌壓力如果不夠的話也是會出現這個問題的，因為打膠機的膠體完全靠氣壓來擠出設備并完美的涂裝在中空玻璃的鋁條中的。如果壓力過小的話也會導致中空玻璃打膠機密封不嚴

　　3, if the pressure of the glue machine is not enough, it will also appear this problem, because the glue of the glue machine is completely squeezed by the air pressure equipment, and perfectly painted in the aluminum strip of the insulating glass. If the pressure is too small, it will lead to the sealing of glass sealing machine is not strict

　　只要我們做到以下的幾點那么我們就能夠有效的降低設備的老化速度保證中空玻璃雙組份打膠機能夠長久穩定的運行。

　　As long as we do the following points, then we can effectively reduce the aging rate of equipment to ensure that the insulating glass two component glue machine can run stably for a long time.

　　一、操作人員好每天都要對打膠機設備的外表上做一番清理。一般要注意要讓殘留的硅膠和雜物灰塵徹底清理干凈，并且要保持工作室內的清理，防止打膠機受到外在環境的干擾。

　　First, the operator is best to fight every day on the surface of the rubber machine equipment to do a clean-up. Pay attention to the residual silica gel and debris, dust thoroughly clean, and to maintain the cleaning room, to prevent the glue machine by external environment interference.

　　二、在保證了打膠機的外表干凈整齊的前提下，要注意防止打膠機的操作中的污染物料污染到打膠機的局部，尤其不能干擾到打膠機的重要零部件，比如槍頭部分等等。

　　Two, to ensure the premise of atx-ii looks clean and tidy, should pay attention to prevent the pollution of material pollution atx-ii operation to local glue machine, especially not interfere with important parts of glue machine, such as gun head etc..

　　三、為了防止打膠機的軸桿以及密封圈老化或者受損，操作人員好定期使用硅油對其進行清洗。清洗完畢后好能保持其干燥，并保證放置在比較封閉的地方。

　　Three, in order to prevent the glue machine shaft and seal aging or damaged, the operator uses the best regular silicone oil to clean it. After cleaning, it is best to keep it dry and make sure it is placed in a relatively closed place.

　　四、我們需要對中空玻璃雙組份打膠機的供膠部分進行定期的清理，比如膠管、混膠器、膠頭等。因為我們加工生產中空玻璃所使用的膠體的特殊性極易有部分膠體殘留在這些零部件內容易造成如出膠不均等故障的出現。

　　Four. We need to regularly clean the rubber parts of the double glazing machine, such as rubber hose, mixer and glue. Because of the particularity of the colloid used in the production of insulating glass, it is easy to have some residual colloid in these parts, which is easy to cause the uneven breakdown of glue.

　　以上便是雙組份打膠機今天的分享，您還滿意嗎，歡迎關注我們的網站:http://www.bjrcc.com.cn并且關注我們的產品，我們將為您提供優良的產品，衷心的愿與您建立合作關系。

　　The above is to share the two-component glue machine today, you still satisfied with it, welcome to our website: http://www.bjrcc.com.cn and pay attention to our products, we will provide you with excellent products, sincerely wish to establish business relationship with you.