Failure of the butyl adhesive coating machine may cause the entire process of insulating glass to stall. The butyl adhesive coating machine is a relatively simple insulating glass equipment. Kangjie Machinery will introduce you to the common faults of the butyl adhesive coating machine and the methods for handling similar faults.

丁基膠涂布機擠出的丁基膠是毛刺不光滑時，如果是新設備，應先觀察出膠孔是否光滑，如果出膠孔粗糙，應先打磨，再試機器；舊機器，可能顯示的溫度與實際的不相符，這時就需要將溫度進行上調，直到出膠正常即可；

When the butyl adhesive extruded by the butyl adhesive coating machine has uneven burrs, if it is a new device, first observe whether the adhesive hole is smooth. If the adhesive hole is rough, first polish it and then try the machine again; For old machines, the displayed temperature may not match the actual temperature, so it is necessary to increase the temperature until the glue is released normally;

丁基膠涂布機打出的膠粘不到鋁隔條上時，可能是原因還是溫度過低，與膠要求的溫度不太符合，只需要咨詢丁基膠提供方需要的溫度，將溫度調整合適即可；

 

When the adhesive produced by the butyl adhesive applicator fails to adhere to the aluminum spacer strip, the most likely reason is that the temperature is too low, which does not meet the required temperature for the adhesive. Simply consult the butyl adhesive supplier for the required temperature and adjust the temperature appropriately;

丁基膠涂布機出現膠頭漏膠，膠頭下面是硅膠墊，估計是硅膠墊損壞導致的，只需要更換硅膠墊即可，但是，需要提醒的是，擠膠壓力過大才是導致硅膠墊損壞的根本原因，不建議將擠膠壓力調的過大；

The butyl adhesive applicator has a leakage of adhesive from the adhesive head, and there is a silicone pad underneath the adhesive head. It is estimated that the silicone pad is damaged, and it is only necessary to replace the silicone pad. However, it should be noted that excessive extrusion pressure is the root cause of damage to the silicone pad, and it is not recommended to adjust the extrusion pressure too high;

丁基膠涂布機的膠頭或膠缸不加熱，估計是加熱棒損壞，更換即可；

The rubber head or rubber cylinder of the butyl adhesive coating machine is not heated, and it is estimated that the heating rod is damaged. Replace it;

丁基膠涂布機的傳送皮帶跑偏，這個應該算不得故障，只需要調整四個角的皮帶輪即可；

The conveyor belt of the butyl adhesive coating machine deviates, which should not be considered a fault. It only needs to adjust the pulley at four corners;

丁基膠涂布機的顯示屏不亮，可以正常使用。這可能是顯示屏損壞或者顯示屏供電線出現問題，更換即可；

The display screen of the butyl adhesive coating machine is not bright and can be used normally. This may be due to damage to the display screen or a problem with the display power supply line, which can be replaced;

本文由臥式丁基膠涂布機整理發布，您是不是對這些內容有所了解了呢?更多的內容請點擊：http://www.bjrcc.com.cn我們會有更多精彩內容等你查看。

This article is organized and released by a horizontal butyl adhesive coating machine. Do you have any understanding of these contents? For more information, please click: http://www.bjrcc.com.cn We will have more exciting content waiting for you to check.